rINSTRUCTION MANUAL FORSEWING MACHINEfelET1®V,9WHITE
FITTING SHANKANDQUILTING SEAM GUIDERaise the presser bar and fit shank as shown. (1) Insert quilting/seam guide carefully so as not to damage the
WINDING THE BOBBIN1. Release stop motion knob.2. Thread as shown.3. Place bobbin onto spindle and hand-wind thread onto bobbin in an anti-clo
REMOVING BOBBIN CASE AND BOBBIN1. Raise needle to its highest position and open the shuttle race cover.bobbin case and pull bobbin case out of ma
INSERTING BOBBIN CASE INTO SHUTTLE RACE1. Ensure needle is at its highest position. Pulling thread to the front, open the latch of bobbin case and ho
THREADING UPPER THREADThread the machine from A to G as illustrated.A. Through the thread guide.B. Between the tension discs.C. Up and into the tensio
DRAWING UP BOBBIN THREADHold the top thread with a slight tension in your left hand and rotate the hand wheel towards you so that the needle goes down
ADJUSTING UPPER THREAD TENSIONFabricUpper threadBobbin threadIt .s only normally necessary to adjust the upper thread tension to achieve the correct b
REGULATING THE PRESSER FOOT PRESSURE1. Adjust lever to desired pressure. For light fabrics use 0-1, for medium fabrics use 1-2, for heavy fabrics use
FABRIC THREAD NEEDLEGUIDEAs a general rule use shorter stitch lengths on finer fabrics and longer stitch lengths with heavier fabrics, finer thread
SEWING {PATTERN SELECTOR) AND OPERATION TABLEStitchNo.Stitch PatternsStitch LengtiPresser FootDrop feed1Straight Stitch11111•04D2Zig-Zag1 Hi•04. * Taa
WHITE SEWING MACHINE COMPANYRecord in space provided below the Serial No. and Model No. of this appliance.The Serial No. is located on Bed Plate.The M
SEWING (PATTERN SELECTOR) AND OPERATION TABLEStitchNo.Stitch PatternsStitch LengthPresser FootDrop feed1Straight Stitch •04n1 aaa2-5Zig-Zag1 III•046Bl
TO START SEWINGImportant Hints.1. Raise the take-up lever to its highest position when starting and stopping sewing.2. Hold both threads about 10 cm
While "2” or "3" on the dial gives a suitable stitch length for ordinary purposes, the stitch length varies with the weight of fabric,
f IaBLIND HEMMINGFold the fabric as illustrated with the "wrong" side facing upwards.d).Place the folded fabric under the foot as shown.Turn
THREE STEP ZIG-ZAGThe three step zig-zag stitch has a wide range of sewing applications, such as patching, darning, repairing tears, mending, sewing o
For thicker fabricsOVERCASTING EDGESBoth these stitches are designed to overlock the edge of a fabric.When the needle is at its extreme right position
The straight stretch sews two stitches forward and one stitch backwards, thereby giving "triple" strengtfi. Use it for stretch fabrics and f
SEWING ON BUTTONS1. Fit darning plate as described on page 12.2. Use button presser foot and attach firmly.3. Place button between presser foot and f
Fit the Zipper foot. The Zipper foot can be moved to the left or right. (2) To sew on the right hand side of the zipper, move foot over to
BUTTON HOLE SEWING Fit the button hole foot.Set the stitch length dial within the green marking to achieve the correct density (closeness) of satin st
IMPORTANT SAFETY INSTRUCTIONSWhen using an electrical appliance, basic safety precautions should always be folowed, including the following:Read all i
HEMMING1. Raise the foot and the needle to its highest position. Replace the foot with the hemmer foot.2. Fold over the fabric edge by about 3mm and
TWIN NEEDLE^P°°' pass the threadsthrough the same procedure but through the eye of each needlerhf;w7'"®r‘''i width, exceedi
Raise the needle bar to its highest point by turning the hand wheel toward you. Open shuttle cover.1) Take out the bobbin case.2) Unlock the shuttle r
CLEANING AND OILINGOpen top cover and oil points indicated.Oil points indicated on underside of bed base. - 27-
TROUBLi-SHOOTING GUIDETop thread breakslower thread breaksSkipped stitchesNeedle breokageStitching forms loopsSeams shrink or puckerIrregular stitchin
WARNING1. Keep fingers away from all moving parts. Special care is required around the sewing machine needle.2. Always use the proper needle plate. Th
CONTENTSName of Parts...Accessories...
NAME OF PARTS (FRONTSIDE)Pattern seJector dial Take up lever Tread tension dial Tread guide for upper threading Presser foot Shuttle cover Extension t
IuSACCESSORIESBobbin1 toaoOil t'', * / à (/FeltButton footButton hole cutter5Zigzag foot (On machine)h 9 ii'r/ 7 ^Screw driver/ r- a /N
REMOVING EXTENSION TABLETo convert the machine from flatHaed to free-arm use simply remove the tension table as shown.THIS IS ONLY APPLICABLE TO MACHI
BEFORE SEWING1. Fit the machine plug into the machine.2. Plug the machine to the power supply.3. Sewing speed can be varied by the speed co
Comments to this Manuals