INSTRUCTION MANUAL FORSEWING MACHINE*3...fa...'( ii fmi Yi 'Afh1UIHIT«
INSERTING BOBBIN CASE INTO SHUTTLE RACE1. Raise needle to its highest position, pulling thread to the front, open the latch of bobbin c
THREADING UPPER THREADTwin needle threading
DRAWING UP BOBBIN THREADHold upper thread with left hand, turn the hand wheel slowly towards you until the needle goes down and comes
CONTROL DIAL1. Pattern selector dial2. Thread tension dial3. Zig-zag width dial Stitch length dial5. Reverse button11
ADJUSTING THREAD TENSIONCorrectWeakStrongUpper thread tension may be adjusted by turning the thread tension dial.FabricUpper threadBobbin threadIncorr
REGULATING THE PRESSER FOOT PRESSURE1. Push down inner pin (A) to increase pressure. (Light to medium fabrics).2. Push down outer ring to release pr
CHANGING NEEDLE1. Raise needle to its highest position.2. Loosen needle clamp screw and remove old needle.3. With the flat side of the needle facin
FABRIC THREAD NEEDLE TABLEPlease note that the following list is a guide when sewing different fabrics.15
SEWING (PATTERN SELECTOR) AND OPERATION TABLE0>PatternZigzag widthStitch lengthPresse? foot3rop fee«1Straight stitch! 14jLp2Zigzag; 1/<<3>
Important Hints.1. Raise the take-up lever to its highest position when starting and stopping sewing.2. Hold both threads about 10 cms to the rear o
WHITE SEWING MACHINE COMPANYRecord in space provided below the Serial No. and Model No. of this appliance.The Serial No. is located on Bed Pla
TO FINISH SEAM1. Sew to the edge of seam.2. Push the reverse button and sew m reverse for about 3—4 cms.3 Raise needle to its highest position.4, Li
STRAIGHT STITCH1. This type of stitching is the one used most frequently.2. The zig-zag presser foot can be used for both straight and zig-zag sewin
OVERCASTING'v'.Use these stitches for oversewing rough edges.STRAIGHT STRETCH STITCHHiMiUse this stitch with knitted, tricot or o
BLIND STITCH1. Fold fabric as shown.2. To finish seam as shown.21
Adjust width and needle position to obtain correct seam.Needle is not piercing edge of fold at all.Needle is pierces edge of fold too much.Corr
BUTTON SEWING(Use darning plate see page 11)1. Lower drop feed.2. Use button presser foot and attach firmly.3 Place button between presser foot and
ZIPPER SEWINGSelect straight stitch.1, Fold the fabric about 2cm and place fabric under foot.2. Zipper foot is designed to sew close to a ra
BUTTON HOLE SEWINGSelect stitch length dial in area indicated.Pattern selector dialStepsSettingsc1. Set dial to "1" position.2. Sew left s
HEMMING3, LOW., <ье ,„0 ,„о» „ .о run into .K.4. Durning sewing, tola mehemmer foot, ^ ^|,^g foot. The, u fwKrif- rlnes not move under the rign
TWIN NEEDLET.™.d .«hln. as .or oorroa, sawio, pass.o, both .breads <bro„,b .be s.rdeL“11'b, wid.b sbodid no. eeceed .be .bird »ides, s.i.cb »i
CONTENTSName of Parts...2
QUILTER1 Insert supporter of quilter.2. Move quilter and adjust stitch distance.28
MAINTENANCE (CLEANING AND OILING)1. Raise needle to its highest position.2. Take out bobbin case.3. Turn latch knob A as illustrated.4. Take off s
CHECKING PERFORMANCE PROBLEMS WHAT TO DOwoPROBLEMFabric not movingBreaking NeedleBreaking Upper ThreadBreadkm Bobbin Th eadPuckeringPROBABLE CAUSEM
NAME OF PARTS (FRONT VIEW)1 Pattern selector dial2 Pressure regulator3 Take up lever4 Thread tension dial5 Presser foot6 Sub-spool pins7 Top cove
(REAR VIEW)Presser foot lever
accessoriesBobbinFeltZigzag foot (On machine)Button footMachine OilZipper footButton hole cutterScrew driverNeedle #11 #14
BEFORE SEWINGConnect light cord, motor wire 2 plugs into power supply separately.1. Remove or install bulb from inside of face cover.2. Open
WINDING THE BOBBIN1. Release stop motion knob.2. Thread as shown.3. When bobbin is filled, tighten stop motion knob.5cm threadPush bobbin winder
REMOVING BOBBIN CASE AND BOBBIN1. Raise needle to its highest position and open the shuttle race cover. bin case out of machine.3. Release the lat
Comments to this Manuals