Singer 14U285B User Manual

14U 10 STITCH OVERLOOK MACHINEOperator’sGuide

• Needle PositionsThree needles can be inserted to the needle clamp on this machine as shown in the sketch but only one or two nee

How to open looper cover(T) Push the cover to the right as far as it will go and(D Pull cover down toward you.Be sure looper cover is closed when sewi

When you wish to change the chainstitch needle thread, left overedge needle thread, right overedge needle thread, left looper thread,

6. How to sew double chainstitchThe double chainstitch is sewn with 2 threads, one needle and one looper. Normally, this machine trim

• To thread the chainstitch looper(4) Threading for chainstitchOpen looper cover. Thread chainstitch looper in the order (f) to (9) as shown. (Purple

(6) Correct thread tensions for double chainstitchBe sure the threads are correctly threaded otherwise proper tension cannot be obtained.Set each tens

7. How to sew twO“thread overlook and overedgeThe 2-thread overlook and overedge is sewn with one needle, one looper and a spreader.(1) Convert right

(2) Thread the left looper (yellow path)Remove cylinder cover and thread left looper in the order (T) to (||) shown below. (Yellow thr

(3a) Thread the right overedge needle for standard 3.5mm stitch widthoTo thread the right needleThread right needle thread in the order ® to

(4) Correct thread tensions for 2-thread wrapped edge overlock.Be sure the threads are correctly threaded otherwise proper tension cannot be obtained.

14U10 STITCH OVERLOOK MACHINEPREFACEThank you for your purchase of this sewing machine.This machine will provide you with excellent performance

(5) Correct thread tensions for 2-thread overedgeBe sure the threads are correctly threaded otherwise proper tension cannot be obtained.Set each tensi

8, How to sew three-thread standard overlook, flatlock and wrapped edge overlookThe 3-thread standard overlock, flatlock and wrapped edge is sewn wit

(4) Correct thread tensions for 3-thread standard overlock.Be sure the threads are correctly threaded otherwise proper tension cannot be obtained.Set

(5) Correct thread tensions for 3-thread flatlock.Be sure the threads are correctly threaded otherwise proper tension cannot be obtained.Set ea

(6) Correct thread tensions for 3-thread wrapped edge overlook.Be sure the threads are correctly threaded otherwise proper tension cannot be obtained.

The 3-thread ultra-stretch is sewn with two needles, one looper and a spreader.( 1 ) Convert right looper into spreader (see page 14)( 2 ) Thread left

The 4-thread ultra-stretch is sewn with two needles, one looper and a spreader.( 1 ) Thread right looper (orange path) (see page 19)( 2 ) Thread left

11. How to sew four-thread safety stitchThe 4-thread safety stitch is sewn with two needles, two loopers and a spreader.( 1 ) Convert right looper int

The 5-thread safety stitch is sewn with two needles, two loopers and three loopers. ( 1 ) Thread right looper (orange path) (see page 19)(2 ) Thread l

13. How to adjust stitch lengthThe stitch length dial on this machine is pre-set to 3mm for normal sewing. Adjust the stitch length t

CONTENTS1.2.3.4.5.6.7.8. 9.10.11.12.13.14.15.16.17.18.19.20. 21. 22.23.24.25.26.27.28.29.30.31.32.33.34.35.PageSelection of stitches ...

5. How to sew rolled hemBoth 1-needle 3-thread and 1-needle 2-thread rolled hem stitching can be performed on this machine. This machin

3. How to adjust thread tensions(1) 1-needle 3-thread• Standard rolled hem stitchingTension DialBlueGreenOrangeY ellowPurple1.02.02.0Right looper thr

Left looper thread wrapped rolled hem stitching (rolled hem variation).• Correct thread tensionA beautiful seam can be obtained on hard-to-roll

16. Differential feed (with differential feed machine only)Differential feed is a system which “stretches” or “gathers” the fabric, when

Stretch overedge is ideal for sewing decorative collars, sleeves, skirt hems, etc. on loosely knit and woven fabrics.• Stretch overedg

17. Free arm sewing (tubular work)Slip tubular work onto the free arm and sew.As shown in figure at left, this machine becomes a free a

20. Three-thread flatlock stitchFlatlock stitch can be used for various applications.Preparation• Use ordinary overedge throat plate.• Use left or

22, Two or three-thread blindstitchingBlindstitching provides a durable hem finish that is almost invisible. It is best suited for sew

24, Two or three-thread pin tuckingPin tucking is a useful decoration when sewing blouses and children’s clothes. Pin tucking is accom

26. Applying elasticElastic may easily be applied using the 3-thread overlock stitch or 4-thread mock-safety stitch.• Knife in non-operating positio

1. Selection of stitchesThis machine is capable of producing various types of stitches according to the combination of needle positions

27. Turning square cornersOutside corner1. Cut out approximately 2cm from the comer in line with the overedge seam edge.2. Sew to point A, one

28. How to replace stationary knifsThe stationary knife (available from your Singer Dealer) should be changed when it becomes dull.The statio

31. LubricationOccasional lubrication is required. The oiling points shown on the figure below should be lubricated periodically.Fig. 2

32, Reasons for poor stitches and how to make adjustmentWhenever sewing difficulty is encountered, make the adjustments as noted below.ConditionReaso

33. Ralationshìp between cloth, thread and needleType of FabricType of ThreadNeedleSinger Cat. No. 2054Light WeightLawn, Organdy, Voil, Crepe, etc.Co

34. Accessories(Accessory Box)1. Needle set 12. Screwdriver (large size) 13. Screwdriver (small size) 14. Tweezers 15. Thread unwinder spool

I7l701Л131Л1

Form U3859 (988) Part No. 379206-002 Printed in Japan

Stitch TypeReferencePages(7) Three-Thread Ultra-Stretch MockSafety Stitch2-needle 3-thread stitch which is ideal for lightweight, extremely stretchy f

2. Handy reference chartStitch TypeNeedlePositionsTension Dial: Numbers shown are average settings on medium weight fabric with standard #80 Polyester

4. Preparation for sewingConnect the machine plug to the electrical receptacle of your machine and the power line plug to the wall

5. Preparation for threading• Setting up the thread guide holderExtend the thread guide holder as far as possible and set the thread guid