Singer W211 User Manual

INSTRUCTION MANUAL MODEL 211 SEWING MACHINE

CHANGING BOBBINSTO REMOVE THE BOBBIN FROM BOBBIN CASE:• Raise needle bar to its highest position. Bobbin case cannot be removed when needle bar isat

THREADING THE BOBBIN CASEPull thread at least 3 inches from bobbin. Insert bobbin in bobbin case so that thread will unravel clockwise.Pull thread i

UPPER THREADINGRaise needle bar to its highest position.Raise presserfoot.Lead thread through top plate thread guide (1) and between tension discs (2)

ADJUSTING FEED DOG HEIGHT(TWIN NEEDLE UPPER THREADING)• Follow threading instruction for single needle with these exceptions.• Place thread, matchin

PICKING-UP LOWER BOBBIN THREAD REGULATING PRESSURERaise presser foot.Holding upper thread, turn hand wheel toward you one rotation. When take-up lever

ADJUSTING UPPER TENSIONTo increase upper tension, turn upper tension regulator to higher number.To decrease upper tension, turn upper tens

FABRIC. THREAD. NEEDLE AND STITCH LENGTH GUIDEFABRICNEEDLE (Lons Scarf), 130/705H ’ Europaar.THREADSTITCH LENGTHDELICATE — tulle, chiffon, voile, fin

Before starting to sew, turn the hand wheel toward you until the needle is at its highest point. NEVER run machine without material

SELECTING NEEDLE POSITIONRight Middle• Three different needle positions, left, "4 " middle and " ◄” right can be selected. Also, those

CHANGINGDIRECTION OF SEWING:• Before changing direction, stop the machine at the desired point making sure that the needle is down through the fabric

for safer sewing ,Please follow these instructions carefully to avoid unexpected 3ccid6ots‘1- Always disconnect the electrical plug from the outlet w

ZIGZAG STITCHINGZigzag Foot(single needle sewing)• Set the needle position dial in the free position• Set the zigzag width control knob from 1 to 5.•

BUTTONHOLE PREPARATIONStep 5,Step!. Step 2. Step 3. Step 4.Seam Ripper0 ea 1 .Needle PosIMon Selector ano Zigzag Width Control DialStitch Length Contr

BUTTONHOLES ON LIGHTWEIGHT OR KNIT FABRICSPlace cord string over tab on presser foot as shown.After finishing the buttonhole, remove the foot f

SEWING ON BUTTONSButton Foot^ 0Other Applications0 a 1 •SHlch Length Control DialPROCEDURE:position with the needle position selectorSet drop feed but

EMBROIDERING0 a 1Needle Position Selector and Zigzag Width Control DialStitch Length Control DialMONOG RAMMINGPROCEDURE:• For free-motion sewing,

SEWING ON ZIPPERSReguler Zipper FoolOo 1 . 2• 3Needle Position Selector and Zigzag Width Control DialStitch Length Control DialPROCEDURE;Set the needl

QUILTING. 4Needle Position Selector and Zigzag Width Control DialStitch Length Control DialPROCEDURE:• Insert the quilter guide bar into the n

CARE AND MAINTENANCEA majority of service calls can be avoided by proper care of your machine. This involves three importantsteps.1 Cleaning Give you

Caution; Eilelore cleaning Ihe machine, be sure to disconnect the power cord trom Ihe wall outletCLEANING THE MACHINECLEANING AND OILING THE HOOK ASSE

OILING-OILSwing open hinged face plate. Apply one drop of oil at all points indicated by arrows.OIL OILOIL OIL OILUsing the large screw drive

features and parts1- Thread Take-up Lever 2. Pressure Release (Darning)3- Top Plate Thread Guide4. Tension Regulator5. Top Plate 6- Handle7. Needle

TROUBLE-SHOOTING GUIDEMACHINE DOES NOT FEEDBOBBIN THREAD BREAKS• Is drop feed up?• Is the bobbin thread jammed in the hook or• Is needle plate correct

accessoriesStraight Stitch FoolButton FoolNeedlesZigzag Foot {In Machine)Ouiliiny GuidePellsBobbinsSeam RipperOilerScrew Driver.

USING THE FOOT CONTROLTO CONNECT THE FOOT CONTROL WIRES:• Connect special plug to block on machine as shown in diagram above.• Connect outlet plug t

FREE ARM FEATURESTUBULAR SEWING• The free arm design simplifies the sewing of tubular items such as pant cuffs, shirt and blouse cuffs and socks.Simpl

CHANGING THE NEEDLEFlat Bide• Afways make sure needle is sfratghf.If straightness of needle, lay needle on a flatSiM isfn parallel as shownin above

CHANGING THE PRESSER FOOTRaise needle bar to highest position and raise presser foot as shown.The extra lift for heavy fabric rriakes it easier

WINDING THE BOBBINTO DISENGAGE THE HAND WHEEL:• Hold the hand wheel (1) with left hand, turn clutch (2) counterclockwise with right’hand to disengage