Singer 14T967DC-WORKBOOK QUANTUMLOCK User Manual

14T967DC Overlock Workbook 

 Thread Chainstitch Looper with a decorative thread 1. Raise the Presser foot to release the tension disks. Pa

 Turn Presser Foot Pressure Dial to “N”.  Turn Differential Feed Dial to “N”.  Turn Seam Width Dial

 Install the Knife Cover.  Engage Upper Looper. Engaging the Upper Looper causes the looper to move when sewing.

Three-Thread Ultra-Stretch Mock Safety Stitch page 6  Engage Spreader. The Upper Looper has a hole for the thread on the top of the lo

Three-Thread Ultra-Stretch Mock Safety Stitch page 7 3. Thread the top cover thread guide by pulling the thread towards the left until

Three-Thread Ultra-Stretch Mock Safety Stitch page 8 10. Thread the looper eye (A) from front to back. Pull about 4 inches of thread.

Three-Thread Ultra-Stretch Mock Safety Stitch page 9 3. Thread the top cover thread guide by pulling the thread towards the left until i

 Thread Left Overedge needle with regular thread. 1. Raise the Presser foot to release the tension disks. Thread the left ne

5. Continue to thread points 4-8. Slip the thread into the middle slot of the thread guide . Go over the take up lever . Continue

 Align two pieces of fabric, right sides together so that that the knife just slightly trims the fabric’s edges.  Sew. T

4. Turn the hand wheel toward you until the Chainstitch Looper extends out 10mm (approximately ½”) from the needle plate edge.

Four-Thread Ultra-Stretch Mock Safety Stitch

Four-Thread Ultra-Stretch Mock Safety Stitch The Four-Thread Ultra-Stretch Mock Safety Stitch is stronger than the Three-Thread Ultra-Stretch Mock

ATD: Auto Tension Dial “A” Left Cover Stitch Needle “C” Not Threaded Middle Cover Stitch Needle “D” Not Threaded Right Cover St

Sweatshirt sample Four-Thread Ultra-Stretch Mock Safety Stitch page 3

 Turn Presser Foot Pressure Dial to “N”.  Turn Differential Feed Dial to “N”.  Turn Seam Width Di

 Install the Knife Cover.  Engage Upper Looper. Engaging the Upper Looper causes the looper to move when sewing.

 Disengage Spreader. The Upper Looper has a hole for the thread on the top of the looper. If the stitch requires that the looper be engage

7. Thread the hole in the Upper Looper from front to back . Pull about 4 inches of thread through the looper and plac

 Thread Middle Cover Stitch Needle with regular overlock thread. 1. Raise the Presser Foot to release the tension disks. Thr

3. Thread the top cover thread guide by pulling the thread towards the left until it slips under the guide. Then pull th

10. Thread the looper eye (A) from front to back. Pull about 4 inches of thread. Position thread into V cutout (B) on threader.

3. Thread the top cover thread guide by pulling the thread towards the left until it slips under the guide. Then pull the thread along

 Thread Left Overlock needle with regular thread. 1. Raise the Presser Foot to release the tension disks. Thread the left ne

5. Continue to thread points 4-8. Slip the thread into the middle slot of the thread guide . Go over the take up lever . Continue

 Fold ribbing lengthwise.  Place ribbing on top of fleece.  Align the fabric so that the knife just slightly trims both

Four-Thread Safety Stitch

Four-Thread Safety Stitch This stitch is an alternative to the Five-Thread Safety Stitch. It offers the same type of Two-Thread Chainstitch. Ho

ATD: Auto Tension Dial “I” Left Cover Stitch Needle “C” Not Threaded Middle Cover Stitch Needle “D” (Orange) Threaded Right C

Four-Thread Safety Stitch page 3  Turn Auto Tension Dial to “I”.  Turn Stitch Length Dial to “N”.  Engage Upper Knife.

5. Continue to thread points 4-8. Slip the thread into the middle slot of the thread guide . Go over the take up lever . Continue by sl

 Turn Presser Foot Pressure Dial to “N”.  Turn Differential Feed Dial to “N”.  Turn Seam Width Di

 Install the Knife Cover.  Engage Upper Looper. Engaging the Upper Looper, causes the looper to move when sewing

Four-Thread Safety Stitch page 6  Engage Spreader. The Upper Looper has a hole for the thread on the top of the looper. I

Four-Thread Safety Stitch page 7 3. Thread the top cover thread guide by pulling the thread towards the left until

Four-Thread Safety Stitch page 8 10. Thread the looper eye (A) from front to back. Pull about 4 inches of thread.

4. Turn the hand wheel toward you until the Chainstitch Looper extends out 10mm (approximately ½”) from the

6. Place the thread through threading guide  and . 7. Continue threading guides , ,  and . 8. Thread the looper e

Four-Thread Safety Stitch page 11 3. Thread the top cover thread guide by pulling the thread towards the left until it slips under t

 Thread Middle Cover Stitch with regular overlock thread. 1. Raise the Presser Foot to release the tension disks. Th

5. Continue to thread points 4-8. Slip the thread into the middle slot of the thread guide . Go over the take up lever . Continue by

 Fuse a layer of fabric to a lightweight batting.  Fuse a fabric backing to the other side of the batting, to create a q

 Place two pieces of broadcloth right sides together.  Align the fabric so that that the knife just slightly trim

Five-Thread Safety Stitch Wide

Five-Thread Safety Stitch (Wide) This stitch is a combination of a Two-Thread Chainstitch and a Three-Thread Overlock Stitch. It is suitable for

Needles: ATD: Auto Tension Dial “B” Left Cover Stitch Needle “C” Not Threaded Middle Cover Stitch Needle “D” (Orange) Thr

Five-Thread Safety Stitch Wide page 3  Turn Auto Tension Dial to “B”.  Turn Stitch Length Dial to “N”.  Engage

 Turn Presser Foot Pressure Dial to “N”.  Turn Differential Feed Dial to “N”.  Turn Seam Widt

 Install the Knife Cover.  Engage Upper Looper. Engaging the Upper Looper causes the looper to move when sewin

Five-Thread Safety Stitch Wide page 6  Disengage Spreader. The Upper Looper has a hole for the thread on the top of the looper.

3. Thread the top cover thread guide by pulling the thread towards the left until it slips under the guide. Then pull the thread along th

7. Thread the hole in the Upper Looper from front to back . Pull about 4 inches of thread through the looper and place to the

 When sewing the Double Chainstitch, it is necessary to have fabric under the needle. Avoid sewing off the fabric.  Continue

4. While holding the thread, firmly, pull the thread between the tension disks. 5. Turn the handwheel toward you until the low

Five-Thread Safety Stitch Wide page 10 10. Thread the looper eye (A) from front to back. Pull about 4 inches of thread. Pos

 Thread Chainstitch Looper with regular overlock thread. 1. Raise the Presser Foot to release the tension d

4. Turn the hand wheel toward you until the Chainstitch Looper extends out 10mm (approximately ½ inch) from the needle plate edge

 Thread Left Overlock needle with regular thread. 1. Raise the Presser Foot to release the tension disks. Thread the left

5. Continue to thread points 4-8. Slip the thread into the foward slot of the thread guide . Go over the take up lever . Continu

 Thread Middle Cover stitch needle with regular overlock thread. 1. Raise the Presser Foot to release the tension disks. Thread the Cover

5. Continue to thread points 4-8. Slip the thread into the middle slot of the thread guide . Go over the take up lever . Continue b

Five-Thread Safety Stitch Wide page 17  Place two pieces of home decorative fabric, right sides together.  Al

Five-Thread Safety Stitch Narrow

Two-Thread Wrapped Edge Overlock (Narrow and Wide)

Five-Thread Safety Stitch (Narrow) This stitch is a combination of a Two-Thread Chainstitch and a Three-Thread Overlock Stitch. It is suitable fo

Set at: ATD: Auto Tension Dial “A” Left Cover Stitch Needle “C” Not Threaded Middle Cover Stitch Needle “D” (Orange) Threaded

Five-Thread Safety Stitch Narrow page 3  Turn Auto Tension Dial to “A”.  Turn Stitch Length Dial to “N”.  Engage

 Turn Presser Foot Pressure dial to “N”.  Turn Differential Feed Dial to “N”.  Turn Seam Width

 Install the Knife Cover.  Engage Upper Looper. Engaging the Upper Looper causes the looper to move when sewin

Five-Thread Safety Stitch Narrow page 6  Disengage Spreader. The Upper Looper has a hole for the thread on the top of the

3. Thread the top cover thread guide by pulling the thread towards the left until it slips under the guide. Then pull the thread along the

7. Thread the hole in the Upper Looper from front to back . Pull about 4 inches of thread through the looper and place to the ba

4. While holding the thread firmly, pull the thread between the tension disks. 5. Turn the handwheel toward you until the lower

Five-Thread Safety Stitch Narrow page 10 10. Thread the looper eye (A) from front to back. Pull about 4 inches of thread. Pos

Two-Thread Wrapped Edge Overlock (Narrow) The Two-Thread Wrapped Edge Overlock provides an elegant fine finish to lightweight fabrics. When usin

 Thread Chainstitch Looper with regular overlock thread. 1. Raise the Presser Foot to release the tension dis

4. Turn the hand wheel toward you until the Chainstitch Looper extends out 10mm (approximately ½ inch) from the needle plate edge.

 Thread Right Overedge needle with regualar overlock thread. 1. Raise the Presser Foot to release the tension disks. Thread the right

5. Before threading the eye of the needle, make sure the thread is behind the thread guide located on the bottom of the needle cla

3. Thread the top cover thread guide by pulling the thread towards the left until it slips under the guide. Then pull the thread a

6. Before threading the eye of the needle, make sure the thread is in front of the thread guide located on the bottom of the need

 Place two pieces of terrycloth right sides together.  Align the fabric so that that the knife just slightly tr

Cover Stitch Narrow

Cover Stitch Narrow This professional Cover Hem stitch is a necessary requirement for today’s sewing. The stitch is often seen in ready-

ATD: Auto Tension Dial “K” Left Cover Stitch Needle “C” (Orange) Threaded Middle Cover Stitch Needle “D” (Blue) Threaded Right

Needle: ATD: Auto Tension Dial “D” Left Cover Stitch Needle “C” Unthreaded and Remove Needle Middle Cover Stitch Needle “D” Unthre

Cover Stitch Narrow  Turn Auto Tension Dial to “K”.  Turn Stitch Length Dial to “2.5”.  Disengage Upper Knife. The knife will

 Turn Presser Foot Pressure Dial to “N”.  Turn Differential Feed Dial to “N”.  Turn Seam Width Dial

 Install the Seam Guide Plate. The Seam Guide Plate provides a flat surface for the fabric and seam guides. It can only be used when the

 Thread Chainstitch Looper with a regular overlock thread. 1. Raise the Presser Foot to release the tens

4. Turn the hand wheel toward you until the Chainstitch Looper extends out 10mm (approximately ½ inch) from the needle plate edge

 Thread Middle Cover needle with regular overlock thread. 1. Raise the Presser Foot to release the tension disks. Threa

5. Continue to thread points 4-8. Slip the thread into the middle slot of the thread guide . Go over the take up lever . Continue by

 Thread Left Cover Stitch needle with regular thread. 1. Raise the Presser Foot to release the tension disks. Thread the l

5. Continue to thread points 4-8. Slip the thread into the forward slot of the thread guide . Go over the take up lever . Contin

 Press a 1” hem into a knit fabric.  Lift the Presser Foot to the highest position.  Position the fabric right side up a

 Turn Auto Tension Dial to “D”.  Turn Stitch Length Dial to “2”.  Engage Upper Knife. The knife will not trim the fabric when

Cover Hem Wide This professional Cover Hem stitch is a necessary requirement for today’s sewing. The stitch is often seen in ready-to-wear

ATD: Auto Tension Dial “H” Left Cover Stitch Needle “C” (Orange) Threaded Middle Cover Stitch Nee-dle “D” Not Threaded Right Cov

Double Chain Stitch  Turn Auto Tension Dial to “H”.  Turn Stitch Length Dial to “N”.  Disengage Upper Knife. The knife will

 Turn Presser Foot Pressure Dial to “N”.  Turn Differential Feed Dial to “N”.  Turn Seam Width Dial

 Install the Seam Guide Plate. The Seam Guide Plate provides a flat surface for the fabric and seam guides. It can only be used when t

 Thread Chainstitch Looper with a regular overlock thread. 1. Raise the Presser Foot to release the te

4. Turn the hand wheel toward you until the Chainstitch Looper extends out 10mm (approximately ½ inch) from the needle plate edge

 Thread Right Cover Stitch needle with regular thread. 1. Raise the Presser Foot to release the tension disks. Thread the

5. Continue to thread points 4-8. Slip the thread into the middle slot of the thread guide . Go over the take up lever . Conti

 Thread Left Cover Stitch needle with regular thread. 1. Raise the Presser Foot to release the tension disks. Thread the l

Congratulations on the purchase of your new SINGER® Quantumlock® Overlock Machine! The Quantumlock® 14967DC is a time sa

 Turn Presser Foot Pressure Dial to “N”.  Turn Differential Feed Dial to “N”.  Turn Seam Width Dial

5. Continue to thread points 4-8. Slip the thread into the front slot of the thread guide . Go over the take up lever . Continue by sl

 Press a 1” hem into a knit fabric.  Lift the Presser Foot to the highest position.  Position the fabric right side up and u

Triple Cover Stitch

Triple Cover Stitch This innovative stitch provides a very wide 5.6 mm professional and creative triple topstitch to sewing projects. Three need

ATD: Auto Tension Dial “J” Left Cover Stitch Needle “C” (Orange) Threaded Middle Cover Stitch Nee-dle “D” (Blue) Threaded Righ

 Turn Auto Tension Dial to “J”.  Turn Stitch Length Dial to “N”.  Disengage Upper Knife. The knife will not trim the fabri

 Turn Presser Foot Pressure Dial to “N”.  Turn Differential Feed Dial to “N”.  Turn Seam Width Dial

 Install the Seam Guide Plate. The Seam Guide Plate provides a flat surface for the fabric and seam guides. It can only be used when t

 Thread Chainstitch Looper with a regular overlock thread. 1. Raise the Presser Foot to release the te

4. Turn the hand wheel toward you until the Chainstitch Looper extends out 10mm (approximately ½ inch) from the needle plate e

 Install the Knife Cover.  Engage Upper Looper. Engaging the Upper Looper causes the looper to move when sewing. Eve

 Thread Right Cover Stitch needle with regular thread. 1. Raise the Presser Foot to release the tension disks. Thread the

5. Continue to thread points 4-8. Slip the thread into the rear slot of the thread guide . Go over the take up lever . Conti

 Thread Middle Cover needle with regular overlock thread. 1. Raise the Presser Foot to release the tension disks. Th

5. Continue to thread points 4-8. Slip the thread into the middle slot of the thread guide . Go over the take up lever . Continue b

 Thread Left Cover Stitch needle with regular thread. 1. Raise the Presser Foot to release the tension disks. Thread the l

5. Continue to thread points 4-8. Slip the thread into the forward slot of the thread guide . Go over the take up lever . Cont

 Press a 3” hem into a woven home decorator fabric.  Lift the Presser Foot to the highest position.  Position the fabric

Three-Thread Rolled Hem

Three-Thread Rolled Hem The Rolled Hem Stitch is used to finish edges of scarves, ruffles, table linens, and some garments. It is suitable for

ATD: Auto Tension Dial “C” Left Cover Stitch Needle “C” Not Threaded Middle Cover Stitch Needle “D” Not Threaded Right Cover St

 Engage Spreader. The Upper Looper has a hole for the thread on the top of the looper. If the stitch requires that the looper be engaged, b

 Turn Presser Foot Pressure Dial to “N”.  Turn Differential Feed Dial to “N”.  Turn Seam Width Dial

 Install the Knife Cover.  Engage Upper Looper. Engaging the Upper Looper causes the looper to move when sewing. Even th

Three-Thread Rolled Hem Page 6  Disengage Spreader. The Upper Looper has a hole for the thread on the top of the looper. I

3. Thread the top cover thread guide by pulling the thread towards the left until it slips under the guide. Then pull the thread along the

7. Thread the hole in the Upper Looper from front to back . Pull about 4 inches of thread through the looper and place to the ba

4. While holding the thread firmly, pull the thread between the tension disks. 5. Turn the handwheel toward you until the lower

Three-Thread Rolled Hem Page 10 10. Thread the looper eye (A) from front to back. Pull about 4 inches of thread. Position thr

 Thread Right Overedge needle with regular overlock thread. 1. Raise the Presser Foot to release the tension disks. Thread the right

5. Continue to thread points 4-8. Slip the thread into the rear slot of the thread guide . Go over the take up lever . Continue by sl

3. Thread the top cover thread guide by pulling the thread towards the left until it slips under the guide. Then pull the thr

 Align a piece of lightweight fabric so that the fabric’s edge is being slightly trimmed by the knife.  Sew.

10. Thread the looper eye (A) from front to back. Pull about 4 inches of thread. Position thread into V cutout (B) on threader.

3. Thread the top cover thread guide by pulling the thread towards the left until it slips under the guide. Then pull the thread along th

 Align two pieces of lightweight fabric, right sides together so that the knife just slightly trims the fabric edge.  Sew.

Two-Thread Wrapped Edge Overlock (Wide) Needle:

 Thread Left Overedge needle with regular thread. 1. Raise the Presser Foot to release the tension disks. Thread the left need

5. Continue to thread points 4-8. Slip the thread into the middle slot of the thread guide . Go over the take up lever . Continue by

Stitch Types: Double Chain Stitch Two-Thread Wrapped Edge Overlock (narrow and wide) Two-Thread Overedge (narrow and wide) Three-Th

 Align one piece of medium weight fabric so that the knife just slightly trims the fabric edge.  Sew. . Two-

Two-Thread Overedge (Narrow and Wide)

Two-Thread Overedge (Narrow) This stitch is used as a lightweight seam finish or a lightweight seam. When creating a seam finish, less thread is

Needle: ATD: Auto Tension Dial “E” Left Cover Stitch Needle “C” Unthreaded and Remove Needle Middle Cover Stitch Needle “D” Unthreade

Two-Thread Overedge (narrow) page 3

 Turn Presser Foot Pressure Dial to “N”.  Turn Differential Feed Dial to “N”.  Turn Seam Width Dial

 Install the Knife Cover.  Engage Upper Looper. Engaging the Upper Looper causes the looper to move when sewing.

Two-Thread Overedge (narrow) page 6  Engage Spreader. The Upper Looper has a hole for the thread on the top of the looper. If the stitc

Two-Thread Overedge (narrow) page 7 3. Thread the top cover thread guide by pulling the thread towards the left until it s

Two-Thread Overedge (narrow) page 8 10. Thread the looper eye (A) from front to back. Pull about 4 inches of thread. Position t

Double Chain Stitch

Two-Thread Overedge (narrow) page 9 3. Thread the top cover thread guide by pulling the thread towards the left until it slips under the

Join two pieces of medium weight fabric, right sides together with a conventional sewing machine straight stitch.  Finsh the edges

Two-Thread Overedge (Wide) The Two-Thread O

ATD: Auto Tension Dial “E” Left Cover Stitch Needle “C” (Orange) Unthreaded and Remove Needle Middle Cover Stitch Needle “D” (Blue) Unthre

 Thread Left Overedge needle with regular thread. 1. Raise the Presser Foot to release the tension disks. Thread the left ne

5. Continue to thread points 4-8. Slip the thread into the middle slot of the thread guide . Go over the take up lever . Continue

 Align one piece of medium weight fabric so that the knife just slightly trims the fabric edge.  Sew.  Align a second piece of me

Three-Thread Overlock (Narrow, Wide, and Wide with Decorative Threads)

Three-Thread Overlock (Narrow) The Three-Thread Overlock Stitch is the most commonly used stitch because of its versatility. It provides a wonde

ATD: Auto Tension Dial “A” Left Cover Stitch Needle “C” Unthreaded and Remove Needle Middle Cover Stitch Needle “D” Unthreaded and Remove

Double Chain Stitch This stitch is suitable for straight seams. It also can be used for a decorative chainstitch topstitching effect. The Middle

The Three-Thread Overlock makes a great edge finish to a garment’s facing. Three-Thread Overlock (narrow) page 3

 Turn Presser Foot Pressure Dial to “N”.  Turn Differential Feed Dial to “N”.  Turn Seam Width Dial

 Install the Knife Cover.  Engage Upper Looper. Engaging the Upper Looper causes the looper move when sewing. Even though

Two-Thread Overedge (narrow) page 7  Disengage Spreader. The Upper Looper has a hole for the thread on the top of the looper. If the

3. Thread the top cover thread guide by pulling the thread towards the left until it slips under the guide. Then pull the thread along the

7. Thread the hole in the Upper Looper from front to back . Pull about 4 inches of thread through the looper and place to the ba

4. While holding the thread, firmly pull the thread between the tension disks. 5. Turn the handwheel toward you until the lower

Three-Thread Overlock (narrow) page 11 10. Thread the looper eye (A) from front to back. Pull about 4 inches of thread. Posit

 Thread Right Overedge needle with regular thread. 1. Raise the Presser Foot to release the tension disks. Thread the right ne

ATD: Auto Tension Dial “D” Left Cover Stitch Needle “C” Unthreaded and Remove Needle Middle Cover Stitch Needle “D” (Blue) Threaded

5. Continue to thread points 4-8. Slip the thread into the rear slot of the thread guide . Go over the take up lever . Continue by sl

 Align one piece of medium weight fabric so that the knife just slightly trims the fabric edge.  Sew.  Align a second piece of medi

Three-Thread Overlock (Wide) The Three-Thread Overedge (wide) has the same set up as the Three-

ATD: Auto Tension Dial “B” Left Cover Stitch Needle “C” Unthreaded and Remove Needle Middle Cover Stitch Needle “D” Unthreaded and Remo

 Thread Left Overedge needle with regular thread. 1. Raise the Presser Foot to release the tension disks. Thread the left ne

5. Continue to thread points 4-8. Slip the thread into the middle slot of the thread guide . Go over the take up lever . Continue

Three-Thread Overlock (Wide—Decorative Thread) Three-Thread Overlock (wide-decorative) page 1 Using deco

ATD: Auto Tension Dial “B” Left Cover Stitch Needle “C” Unthreaded and Remove Needle Middle Cover Stitch Needle “D” Unthreaded and Remo

Double Chain Stitch  Turn Auto Tension Dial to “D”.  Turn Stitch Length Dial to “N”.  Disengage Upper Knife. The knife will not

5. Turn the handwheel toward you until the lower looper extends 5-10mm (approximately ½ inch) from the needle plate edge. 6. Thread t

 Thread Lower Looper with decorative overlock thread. 1. Raise the Presser Foot to release the tension disks. Thread the Lower

6. Thread the looper area of the machine following the red color coded thread guides 4-10. 7. Place the thread slighty from left and

 Thread Overedge Left needle with regular thread. 1. Raise the Presser Foot to release the tension disks. Thread the lef

Three-Thread Overlock (wide-decorative) page 8 5. Continue to thread points 4-8. Slip the thread into the middle slot of the thread

 Align double-sided quilted fabric so that the knife just slightly trims the fabric edge.  Sew. Three-Thread Overlo

Three-Thread Flatlock (Narrow and Wide)

Three-Thread Flatlock (Narrow) The Flatlock Stitch is used decoratively to achieve the look of applied trim on a garment, craft or home decorator

Needle: ATD: Auto Tension Dial “F” Left Cover Stitch Needle “C” Unthreaded and Remove Needle Middle Cover Stitch Needle “D” Unthr

The Flatlock stitch, with fabric’s right sides together, form a ladder stitch. A ribbon can then be woven by hand in and out of the stitches. The

 Turn Presser Foot Pressure Dial to “N”.  Turn Differential Feed Dial “N”.  Turn Seam Width Dial t

Three-Thread Flatlock (narrow) page 4

 Turn Presser Foot Pressure to “N”.  Turn Differential Feed Dial to “N”.  Turn Seam Width Dial

 Install the Knife Cover.  Engage Upper Looper. Engaging the Upper Looper causes the looper to move when sewing. Even t

Two-Thread Flatlock (narrow) page 8  Disengage Spreader. The Upper Looper has a hole for the thread on the top of the looper. If th

3. Thread the top cover thread guide by pulling the thread towards the left until it slips under the guide. Then pull the thread along th

7. Thread the hole in the Upper Looper from front to back . Pull about 4 inches of thread through the looper and place to the

Three-Thread Flatlock (narrow) page 11 10. Thread the looper eye (A) from front to back. Pull about 4 inches of thread. Pos

 Thread Right Overedge needle with regular overlock thread. 1. Raise the Presser Foot to release the tension disks. Thread the right

5. Continue to thread points 4-8. Slip the thread into the rear slot of the thread guide . Go over the take up lever . Continue by

 Install the Seam Guide Plate. The Seam Guide Plate provides a flat surface for the fabric and seam guides. It can only be used when the

 Fold T-shirt interlock fabric wrong sides together lengthwise.  Align the fabric so that the fabric’s fold is not

Three-Thread Flatlock (Wide) Three-Thread Flatlock (wide) page 1 The Three-Thread Flatlock (wide

ATD: Auto Tension Dial “F” Left Cover Stitch Needle “C” Unthreaded and Remove Needle Middle Cover Stitch Needle “D” Unthreaded and R

Three-Thread Flatlock (wide) page 3 Decorative Ladder Effect (wide) Decorative Loop Effect (wide)

 Thread Left Overlock needle with regular thread. 1. Raise the Presser Foot to release the tension disks. Thread the left

5. Continue to thread points 4-8. Slip the thread into the middle slot of the thread guide . Go over the take up lever . Continu

 Fold sweatshirt fabric wrong sides together, lengthwise.  Align the fabric so that the fabric’s fold is not being

Three-Thread Ultra- Stretch Mock Safety Stitch

Three-Thread Ultra-Stretch Mock Safety Stitch This stitch stretches with the fabric, the seam will not break when the fabric is stretched. It

Needle: ATD: Auto Tension Dial “G” Left Cover Stitch Needle “C” Not Threaded Middle Cover Stitch Needle “D” Not Threaded Righ