Singer W120 User Manual

tit<19INSTRUCTION,0« SE..0

9. HOW TO SEW STRAIGHT STITCHES(1) Prepare for Sewing as Follows:(a) Set the zigzag width regulating knob to "0" (zero position). Now you

(a) Stop sewing with the needle in the cloth(c! L»:: 2 izzpresser root and resume sewing,(4) How to Remove the Cloth:(a) When the needle bar has reach

is produced, (looping on the bottom)(6) How to Adjust the Tension of the Upper Thread(b) Turn the tension disc to the right to increase the tension.(c

10. ADJUSTMENT OF STITCHES AND REVERSE SEWING(a) The figures on the indicating plate (3) show the stitch length.(b) Turn the knob (1) setti

12. ADJUSTMENT OF PRESSURE TO CLOTH(a) In the case of ordinary cloth, it is seldom necessary to adjust the pressure, but when sewing t

13. REGULATING WIDTH OF ZIGZAG STITCHThe width of tlgtag stitch Is regulated by the zigsae width ,rigtag width lever to desire zlzzae stlth "Idt

14. MANUAL ZIGZAG SEWINGBy manually adjusting Che stitch length, zigzag width while running the machine, a variety of omamental stitches are sewn.fol

IS. HOW TO KEEP THE MACH/NPOiling CHINE IN GOOD repairIS SQ important that ifot only shorten the ^ should be neaTnT , roachine'Q '^^glig

HOW TO MAKE BUTTON HOLESPlace a marking needle across the cutting space to protect the stitching.1. Kemove the regular presser foot and attach t-ho k2

Pr*esser foot апи •end to brine thp к ^s^ng the needlp я-7 feed tep^ь u'• the eigeag width J drop f„d ttaok. (2) ** ® at '4., P f

CONTENTS.1'"1.2.3.4.5.6.7.8. 9.10.11.12.13.14.15.16.17.18.19.20. 21. 22.Name of parts...

17. DARNING AND EMBROIDERYRaise the presser bar lifter and remove the presBei. foot. Then lower the presser bar lifter to ensure the thr

18. SEWING ON BUTTONS(b))-op.,..,(c) Place the button under th^ kfcot. Get both holes c rfoot evenly. centered under the(<i) Turn the balance w

19. NARROW HEMMINGTurn balance wheel towards you until needle reaches its highest point. Raise presser bar and remove the regular presser foot. Atta

20. SEWING IN A ZIPPERThe Zipper foot included in the arrpce^ •rlc. accessories enables you to attach a tipper „„ feb-Remove the regular presser foot

21. INSTALLING SEWING HEAD IN CABINET OR PORTABLE BASEHi HEAD HINGE HOLES^22(1) CABINET1. Back off both head hinge set screws until head hinge hole is

(2) PORTABLE BASE 23-

22. BLIND HEMS◄ R1. Usfe blind stitch cam. NO. 82. Use standard zigzag presser foot3. Set needle position lever in right notch marked4. Set zigzag

1. NAME OF PARTS^ ? 29 1 2 28 27ni A*1. Spool pin2. Zigzag width control knob3. Bobbin winder thread guide4. Top cover thread guide5. Thread take-

2. TUENING ON LIGHTThe lamp housing is enclosed in the face plate (Fig 2).The switch for operating the light is beneath the face plate (Fig 3).Changi

3. WINDING THE BOBBINThe bobbin is easily wound by the following method.(a) Turn the stop motion knob (1) toward you while holding the balance wheel(

4. INSERTING OF THE NEEDLE(a) Loosen the needle clamp with your right hand and hold needle so that the flat side is to your right.

5. HOW TO THREAD THE NEEDLE(a) Raise the needle bar to its highest point.(b) Thread the needle by following the numbers indicated in the picture.(1) A

6. HOW TO REMOVE THE BOBBIN CASE(a) Raise the needle bar to its highest point by turning the balance wheel.(b) Open the bobbin case cover.(c)

(a) Hold the bobbin in your right hand, pull out the thread about 5 inches, and insertin the bobbin case. (Fig. A)(b) Pull the thread through the slot