SINGER P-1250 Instruction Manual Page 19

  • Download
  • Add to my manuals
  • Print
  • Page
    / 46
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 18
17
72
Twin needle sewing produces two parallel lines
of closely-spaced decorative stitching. You can
sew with either one or two thread colors.
Your machine is not suplied with the twin needle
or spool pin. These may be obtained from your
local retailer as optional accessories.
Recommended settings
Stitch Selection: Desired stitch
Needle Position:
Stitch Width:
Stitch Length: 2-5
Foot: General Purpose (B)
Needle Plate: General Purpose (A)
Turn the machine off.
Insert the twin needle with the flat side of the
shank towards the rear of the machine.
Thread the machine as you normally would for
single needle stitching, and pass the thread
through the left eye of the twin needle.
Insert a second spool pin into the hole on the
top cover of the machine, as illustrated.
Thread the machine in the usual way.
Pass the thread through the remaining points,
making certain to omit the thread guide just
above the needle and pass thread through
right eye of needle.
Draw both threads under the foot and back
along with the bobbin thread.
Slowly lower the needle into the hole in the
needle plate by turning the hand wheel toward
you to make sure the needle clears the plate.
Caution:
Make sure not to use a stitch width greater
than that which is recommended when twin
needle stitching.
Twin needle
sewing
7
3 4 51 2
La costura con aguja doble produce dos
lineas paralelas de puntos decorativos
debidamente espaciadas.
Su máquina no ha sido complementada ni
con una aguja doble ni con el portacarrete
adicional. No obstante si desea utilizar esta
ventaja, puede adquirir estos accesorios en
su Centro de Costura.
Posiciones recomendadas
Selección punto: el deseado
Posición aguja:
Anchura punto:
Longitud punto: 2-5
Prensatelas: Uso general (B)
Plancha aguja: Uso general (A)
Desconecte la máquina.
Inserte la aguja doble con el lado plano del
tronco hacia atrás.
Enhebre la máquina como lo haría
normalmente para coser con una aguja,
pasando el hilo a través del ojo izquierdo
de la aguja doble.
Coloque el segundo portacarrete en su
agujero situado en la cubierta superior,
como se ilustra.
Enhebre la máquina en la forma usual.
Pase el hilo a través de los puntos
restantes, cuidando de no hacerlo por el
guía hilo existente sobre la aguja y, a
través del ojo derecho de la aguja.
Tire de ambos hilos hacia atrás, por debajo
del prensatelas,junto con el hilo de la
bobina.
Baje despacio la aguja hacia dentro del
agujero de la plancha de aguja, girando el
volante hacia Vd., para asegurarse que la
aguja salva el agujero de la placha.
Precaución:
Asegúrese de no utilizar una anchura de
punto mayor que la recomendada al
coser con aguja doble.
Costura con
aguja doble
3 4 51 2
20
21
16
15
24
P/N 362095
sa
s
s s
s
sa
a
a s
a a
a a a s s
a
a s s
sa
s
sa
sa
a a
sa
ss
a
sa
a s sa
a s sa
sa
asa
sa
s
s
sa sa
a a
a a
sa
a
sa s s
sa
aa
as
as
s a a
as
a s
as
a
s s
sa
a as
asas
sa
s sa
ss
a
s
a
a
sa
as
a s
asas
a s
a s
sa
sa
a
s
a s
sa as
s
a
a
a s
sas sa
sa
s ss
a
asa
sa
as
aa
a
s
S
IN
G
E
R
aa
as s
27
26
25
23
13
17
1
2
4
9
8
7
10
11
12
14
19
18
6
5
3
22
Page view 18
1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 45 46

Comments to this Manuals

No comments